STANDARD CURE POWDER COATING BASED ON POLYESTER DESIGNED FOR ARCHITECTURAL APPLICATION
| Standard Packaging | 10 kg & 20 Kg cartons |
| Specific Gravity | 1.3 -1.7 g/cm3 depending on colors |
| Storage Stability | Use before: 6 months (from month of mfg). Store below 30°C, avoid direct and extended heat exposure. |
| Finish | Gloss* |
|---|---|
| Smooth Glossy | 90 - 95 |
| Smooth Semi-Glossy | 45 - 65 |
| Matt | 5 - 15 |
| Fine Texture | -- |
| Structure | -- |
All RAL colors are available. Special custom colors can be made available upon inquiry with a minimum order of 100 kg. Fine texture finishes require a 150 kg minimum order. * Gloss level at 60° angle (doesn‘t apply to metallic effect powder coatings).
| Steel | Alum inum | Galva nised | Cast Steel | HR Steel | |
|---|---|---|---|---|---|
| Degreasing | Yes | Yes | Yes | Yes | Yes |
| Chromating | Yes | ||||
| Chrome Free | Yes | ||||
| Derusting | Yes | Yes | Yes | Yes | |
| Iron Phosphate | Yes | ||||
| Zinc Phosphate | Yes | Yes | Yes | ||
| Blasting | Yes | Yes | |||
| Sweep Blast | Yes |
Processing Instructions: The guidelines for application must be strictly observed.
| Test | Test Method | Series PP
Glossy | Series PP
Semi-Glossy | Series PP
Matt | Series
Texture | Series
Structure |
|---|---|---|---|---|---|---|
| Film Thickness microns | ISO 2360 | 50 - 60 | 50 - 60 | 50 - 60 | 60 - 70 | 80 - 100 |
| Gloss @ 60° | ISO 2813 | 90 - 95 | 50 - 65 | 5 - 15 | NA | NA |
| Adhesion | ISO 2409 | Gt-0 | Gt-0 | Gt-0 | Gt-0 | Gt-0 |
| Bending | ISO 1519 | 6 mm | 6 mm | 6 mm | 6 mm | 6 mm |
| Impact Resistance inlb | ASTM D2794 | 40 – 160 | 40 – 160 | 40 – 160 | 40 | 40 |
| Pencil Hardness | ASTM D3363 | H – 2H | H – 2H | H – 2H | H – 2H | H – 2H |
| Salt Spray Test | ASTM B117 | 1000 hours | 1000 hours | 1000 hours | 1000 hours | 1000 hours |
Note: Above tests done on Chromated Aluminium
The information in this data sheet is not intended to be exhaustive and is based on the present state of our knowledge and on current laws: any person using the product for any purpose other than that specifically recommended in the technical data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. It is always the responsibility of the user to take all necessary steps to fulfill the demands set out in the local rules and legislation. Always read the MSDS and the TDS for this product. All advice we give or any statement made about the product by us (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing otherwise, we do not accept any liability whatsoever for the performance of the product or for any loss or damage arising out of the use of the product. All products supplied and technical advices given are subject to our standard terms and conditions of sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is subject to modification from time to time in the light of experience and our policy of continuous development. It is the user's responsibility to verify that this data sheet is current prior to using the product.
with local technical support