Zinc Rich Epoxy Powder Coating

Homepage
/
ZincGuard
/

Product Data Sheet

STANDARD CURE POWDER COATING BASED ON POLYESTER DESIGNED FOR ARCHITECTURAL APPLICATION

Typical applications

  • Fencing
  • Petrol Dispenser
  • Lamp Post
  • Control Panel
  • Transformer
  • Genset Canopy

Product Performance

Standard Packaging10 kg & 20 Kg cartons
Specific Gravity1.3 -1.7 g/cm3 depending on colors
Storage StabilityUse before: 6 months (from month of mfg).
Store below 30°C, avoid direct and extended heat exposure.

Features

  • Good Leveling
  • Good chemical resistance
  • Good corrosion resistance

Application guide

Surface Preparation
DegreasingAlkaline Degreaser
H R SteelShotblasting to SA 2½
Sheet MetalPassivated Zinc Phosphate
(Coating wt 1.5 – 2.5 gms/ Sq.M)
Single CoatTwo Coat
Voltage40 – 90 KV40 – 90 KV
CuringEffective Metal TemperatureEffective Metal Temperature
Prime-H180°C/10–15 min180°C/3–5 min
Hybrid Top Coat---180°C/10–15 min
Polyester Top Coat---190°C/10–15 min

The guidelines for application must be strictly observed.

Pretreatment

SteelAlum inumGalva nisedCast SteelHR Steel
DegreasingYesYesYesYesYes
ChromatingYes
Chrome FreeYes
DerustingYesYesYes
Iron PhosphateYes
Zinc PhosphateYesYesYesYes
BlastingYesYes
Sweep BlastYes

Processing Instructions: The guidelines for application must be strictly observed.

Performance (When cured at 180°C/ 10 Min EMT)

TestTest MethodSeries EPZ
Film Thickness micronsISO 2360Film Thickness microns
Gloss @ 60°ISO 2813Gloss @ 60°
AdhesionISO 2409Adhesion
BendingBendingBending
Impact Resistance inlbImpact Resistance inlbImpact Resistance inlb
Pencil HardnessPencil HardnessPencil Hardness
Salt Spray TestSalt Spray TestSalt Spray Test

Prime-H + TriBond Polyester Toap Coat

PretreatmentSolvent Degrease -> Blast clean SA 2½
Profile 50 – 60 mic
Tricationic Zinc Phosphate
Water Rinse -> Dry
Neutral Salt Spray2000 HrsMax 9 mm CreepMax 1 mm Creep
4000 HrsMax 17 mm CreepMax 7 mm Creep
Natural Exposure18 monthsMax 3 mm CreepMax 4 mm Creep

Note: Above tests done on Tricationic Zinc Phosphated Steel

Disclaimer

The information in this data sheet is not intended to be exhaustive and is based on the present state of our knowledge and on current laws: any person using the product for any purpose other than that specifically recommended in the technical data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. It is always the responsibility of the user to take all necessary steps to fulfill the demands set out in the local rules and legislation. Always read the MSDS and the TDS for this product. All advice we give or any statement made about the product by us (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing otherwise, we do not accept any liability whatsoever for the performance of the product or for any loss or damage arising out of the use of the product. All products supplied and technical advices given are subject to our standard terms and conditions of sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is subject to modification from time to time in the light of experience and our policy of continuous development. It is the user's responsibility to verify that this data sheet is current prior to using the product.

Complete powder coating solutions 

with local technical support

Contact Us

Colour Selector

SDS/TDS

Resources

About Us

TRICOLOUR SPECIALITIES is a young organization, shaped by highly experienced industry professionals, producing and marketing thermoset powder coatings.

Call Now: +91 9909877847

Best Services
Contact Info

Plot No. 303/7, Vapi Papermill Road,
2nd Phase, GIDC, Vapi - 396195

+91 9724805656

tricolour.vapi@gmail.com

tricolourspecialities.com

Newsletters

Subcribe for all news from us. Please enter your email to form below.